https://techproces.com/ pump-cavitation-and-prevention
https://techproces.com/ pump-cavitation-and-prevention

Pump Cavitation And Prevention.

Pump Cavitation And Prevention.

Preventing cavitation of a pump is a significant operation for the smooth and efficient operation of a pump. Failure to prevent sin cavitation can result in complete damage to the pump impeller or pump. Which prevents any process from running smoothly. The term pump cavitation refers to conditions within the pump that where the actual suction pressure drop below the vapor pressure of the liquids, at the corresponding temperature. Abnormal sound, vibration occurs in the pump during cavitation, and delivery pressure and flow rate decrease.

 

https://techproces.com/ pump-cavitation-and-prevention
https://techproces.com/ pump-cavitation-and-prevention

 

# The suction pressure drop May be produced by one of the following reasons:

  • An increase in the static lift of the centrifugal pump.

  • A decrease in the atmospheric pressure with a rise in the altitude.

  • A decrease in the absolute pressure in the system.

  • As in the case of pumping from closed vessels.

  • An increase in the temperature of the pumping liquid and

  • Increase in velocity by speeding up the pump.

  • The Net Positive Suction Head or NPSH is less than the liquid vapor pressure.

  • Over speed of the driver.

  • Section pipe not sufficiently submerged.

  • Pump fluid passage has obstructed.

  • Excess air and gases in the fluid.

  • Please also check the article: Centrifugal Pump & Troubleshooting.

# Pump Cavitation may affect in operation as:

  • Create noise and vibration

  • The impeller can be damage by vane pitting, corrosion, erosion fatigue failure of metals.

  • Drop-in head vs capacity and efficiency curves.

  • Batch processes or continuous processes may be discontinued.

  • Organizations can face huge losses.

# Prevention of centrifugal pump cavitation:

  • In this case, adjust the Suction lift.

  • In this case, the line from the suction to the pump should be filled with liquid to expel the air and the casing vent of the pump should be opened and purged until the air is free.

  • Consult with the manufacturer.

  • In case, the suction pipe or flange leak, then rectify the leak.

  • You need to check if the discharge of the pump is open enough.

  • Increase the diameter of the suction pipe.

  • Reduce the length of the suction pipe.

  • Install a suction stabilizer.

  • sub-cool the liquid to decrease the suction temperature.

  • Please also check the article: Centrifugal Pump & Troubleshooting.

# NPSH:

To avoid Pump cavitation, the pleasure at the Pump Inlet must exceed the vapor pressure (Pv) of the liquid, at the corresponding temperature by a certain value, the called net positive suction head or NPSH.

The net positive suction head or NPSH is the total suction head less than the vapor pressure (Pv) of the liquid, expressed in feet (Meters).

 

https://techproces.com/ pump-cavitation-and-prevention
https://techproces.com/ pump-cavitation-and-prevention

The NPSH can be shown by the following equation and figure:

NPSH ≥ ( Hts – Pv)
Where;   Hts= ( Patm  +  Pgs  +  Hvs  –  Hfs ± Z )

Hts = Total suction head, 

Patm = Atmospheric pressure,

Pgs = Gage   pressure,

Hvs = Suction velocity head,

Hfs = Suction line friction loss,

 Z = Suction elevation head,

Pv = Vapor pressure of the liquid at corresponding Temperature,

# Increase the NPSH the following attempt can be taken;

  • Increase the diameter of the suction pipe.

  • Reduce the length of the suction pipe.

  • Install a suction stabilizer.

  • Elevate the suction liquid level.

  • Sub-cool the liquid.

About Tech Process

Check Also

https://techproces.com/ Turbine-Compressor-Process-Industries

Question With Answer About Turbine And Compressor In Process Industries 02.

Question With Answer About Turbine And Compressor In Process Industries.     The turbine is …

https://techproces.com/ Knowledge Of Oil & Gas Process Technology.

Question With Answer About Turbine And Compressor In Process Plant 01.

Question With Answer About Turbine And Compressor In Process Plant.   The turbine is a …

https://techproces.com/ General Question With Answer About Turbine And Compressor Knowledge Of Oil & Gas Process Technology.

What Is Compressor And Compression System? Working Principal Of Compressor.

What Is Compressor And Compression System? Working Principal Of Compressor. A compressor is a mechanical …

https://techproces.com/Sewage Or Wastewater Treatment Process. Knowledge Of Oil & Gas Process Technology.

Sewage Or Wastewater Treatment Process.

Sewage Or Wastewater Treatment Process. Sewage Or WasteWater treatment processes are primarily designed to purify …

https://techproces.com/Fire-Hazards-Workplace/

How To Prevent Fire Hazards In The Workplace?

Let’s We Know About Fire Hazard And How To Prevent Fire Hazards In The Workplace. …

This site uses Akismet to reduce spam. Learn how your comment data is processed.